AWLCRAFT CS CONVERTER

What it is and why choose AWLCRAFT CS CONVERTER

AWLCRAFT CS CONVERTER (Awlcraft CS – Curing Solution OJ0010) is the dedicated Part B for the Awlcraft CS two-component clearcoat system from Awlgrip. Formulated for the yacht market, it is used in combination with Awlcraft CS Low Gloss Base (OJ0300) and Medium Gloss Base (OJ0301) to create durable matt, satin, semi-gloss or gloss finishes on small and large areas. When correctly mixed with the base component and reducer, it enables consistent curing, reliable film build and the high-quality appearance associated with Awlcraft CS.

Main features

• Curing solution (converter) specifically for Awlcraft CS clearcoat.
• Part of a two-component, intermixable clearcoat system designed for yachts.
• Enables a wide range of gloss levels, from matt/flat to gloss, depending on the base mix used.
• Suitable for application on both small parts and larger yacht areas.
• Compatible with Awlcraft SE basecoat colors and effects; can also be used over Awlcraft 2000, Awlgrip Topcoat and Awlgrip HDT when properly prepared.
• Designed for air atomized spray application.
• Supplied in 1 US gallon packs for professional use.

Technical specifications

• Product type: Converter / curing solution for Awlcraft CS clearcoat.
• Product code: OJ0010 (Part B).
• System volume solids: 46.4% (Awlcraft CS system).
• Available pack size: 1 US gallon (≈ 3.78 L) for base and curing solution.
• VOC (as supplied, without reducer – OJ0010 Part B): 360 g/L; 3.01 lb/gal.
• Recommended application method (system): Air atomized spray only; electrostatic spray is not permitted.
• Theoretical coverage (mixed Awlcraft CS, air atomized):
  • Recommended coats: 2
  • Recommended wet film thickness (per coat): 75 μm (3 mil)
  • Recommended dry film thickness (per coat): 35 μm (1.4 mil)
  • Theoretical coverage: 13.2 m²/L; 537.8 ft²/gal at recommended DFT
• Mix ratio (Base : Converter : Thinner, by volume): 100 : 40 : 60 with Reducer T0002 or T0003.
• Alternative mix ratio: 2.5 : 1 by volume (Base : Converter), then add 40% thinner.
• Recommended reducers: T0002 or T0003.
• Application equipment (air atomized, system data):
  • Fluid tip: 1.20 – 1.40 mm (47 – 55 thou)
  • Air pressure at gun: 2 – 2.4 bar (29 – 35 psi)
• Drying times of mixed Awlcraft CS at recommended DFT:
  • 15°C (59°F): Touch dry 5 h; hard dry 6 h
  • 25°C (77°F): Touch dry 3 h; hard dry 5 h
  • 35°C (95°F): Touch dry 2 h; hard dry 3 h
• Pot life of mixed Awlcraft CS:
  • 15°C (59°F): 90 minutes
  • 25°C (77°F): 90 minutes
  • 35°C (95°F): 60 minutes
• Recoatability with Awlcraft CS (using OT0003):
  • 15°C (59°F): Recoat after min. 8 h, max. 24 h
  • 25°C (77°F): Recoat after min. 6 h, max. 24 h
  • 35°C (95°F): Recoat after min. 6 h, max. 24 h
• Overcoating with T0002 reducer (small scale): Maximum overcoating window of 30 minutes between coats.
• Surface and ambient conditions for application (system):
  • Substrate temperature: 5–30°C (41–86°F)
  • Product temperature: 15–35°C (59–95°F)
  • Ambient temperature: 5–35°C (41–95°F)
  • Apply in a well-ventilated area; avoid direct sunlight and late-evening application to prevent gloss loss from condensation.
• In-tent applications: Recommended airflow of 0.5–0.6 m/s (1.64–1.96 ft/s).

Applications and use cases

Intended uses in the Awlcraft CS system

• Designed as the curing solution for Awlcraft CS two-component matt clearcoat for yacht applications.
• Suitable for creating finishes on both small details and large hull or superstructure areas when used with Awlcraft CS bases.

Compatible substrates and systems

• Awlcraft CS should be applied over Awlcraft SE Basecoat; the converter is used as Part B of this clearcoat system.
• Can also be used (as part of the Awlcraft CS mix) over properly sanded and cleaned:
  • Awlgrip Topcoat
  • Awlgrip HDT
  • Awlcraft 2000
• Over existing Awlgrip Topcoat, Awlgrip HDT and Awlcraft 2000, surfaces must be sanded with P400 to remove gloss and then cleaned with Surface Cleaner T0170 (US/AP) or T0340 (EU) using the two-cloth wipe-down method.

Gloss level options when used with Awlcraft CS bases

By combining AWLCRAFT CS CONVERTER with specific ratios of Awlcraft CS Low Gloss Base (OJ0300) and Medium Gloss Base (OJ0301), the following finishes are achievable:

• Matt/Flat (0–15 gloss units at 60°): 100 parts OJ0300.
• Satin (16–30 gloss units at 60°): 60 parts OJ0300, 40 parts OJ0301.
• Semi-gloss (31–60 gloss units at 60°): 30 parts OJ0300, 70 parts OJ0301.
• Gloss (61–85 gloss units at 60°): 100 parts OJ0301.

Mix ratios are advisory and gloss levels may show slight deviation. Application on a test panel is recommended to confirm the desired gloss before full-scale application.

FAQ

1. What is AWLCRAFT CS CONVERTER used for?

It is the curing solution (Part B) for the Awlcraft CS two-component clearcoat, enabling proper chemical curing and performance of the mixed product.

2. Which bases is this converter compatible with?

It is designed to be used with Awlcraft CS Low Gloss Base (OJ0300) and Awlcraft CS Medium Gloss Base (OJ0301).

3. What mix ratio should I use with the base and thinner?

The recommended mix ratio is 100 parts Base : 40 parts Converter : 60 parts Thinner by volume, using reducer T0002 or T0003. Alternatively, 2.5 parts Base : 1 part Converter, then add 40% thinner.

4. Can the mixed Awlcraft CS be applied with electrostatic spray equipment?

No. This product cannot be applied using electrostatic spray application methods. Air atomized spray is recommended.

5. Over which coatings can the Awlcraft CS system be applied?

Awlcraft CS can be applied over Awlcraft SE Basecoat, and over sanded Awlgrip Topcoat, Awlgrip HDT and Awlcraft 2000 that have been prepared with P400 and cleaned with the specified surface cleaners.

6. What are the typical drying times for the mixed Awlcraft CS system?

At 25°C (77°F) the system is typically touch dry in 3 hours and hard dry in 5 hours. At 15°C (59°F) it is touch dry in 5 hours and hard dry in 6 hours; at 35°C (95°F) it is touch dry in 2 hours and hard dry in 3 hours.

7. How long can I use the product after mixing (pot life)?

Pot life is approximately 90 minutes at 15–25°C (59–77°F) and 60 minutes at 35°C (95°F).

8. What is the recommended recoat window for Awlcraft CS?

Using OT0003, Awlcraft CS can typically be recoated after 8–24 hours at 15°C, 6–24 hours at 25°C and 6–24 hours at 35°C on unsanded Awlcraft CS.

9. Which reducers can I use with this converter in the Awlcraft CS mix?

Reducer T0003 is recommended; T0002 can be used for small-scale applications, observing a maximum overcoating window of 30 minutes between coats.

10. Where can I find additional technical details not listed here?

Consultar ficha técnica del fabricante.

Section 14 – Transport information

Consultar ficha técnica del fabricante.

Section 8 – Personal protective measures

Consultar ficha técnica del fabricante.

*Contenido generado por IA