TOPCOAT SPRAY FAST REDUCER T0001

What is TOPCOAT SPRAY FAST REDUCER and why choose it

TOPCOAT SPRAY FAST REDUCER (Awlgrip T0001) is a fast evaporating reducer formulated for spray-applied urethane topcoats. It is designed for use in Awlgrip, Awlcraft 2000 and Awlcraft SE topcoats, as well as selected Awlgrip primers. Within the specified temperature range, it keeps the paint film open long enough to promote good flow while evaporating quickly enough to deliver adequate dry and dust-free times. With a VOC content of 888 g/L (7.4 lbs/gallon) and a carefully balanced solvent blend, this reducer helps optimize spray application and film appearance under moderate temperature conditions.

Main features

• Fast evaporating reducer specifically for spray-applied urethane topcoats.
• Optimized for 60–75°F (16–24°C) application and cure temperatures.
• Supports good flow and leveling by keeping the paint film open while still allowing fast dry and dust-free times.
• Compatible systems: Awlgrip, Awlcraft 2000 and Awlcraft SE topcoats.
• Primer use: also recommended for Quik-Grip Primer and Awlbrite Quik-Fil Clear.
• Physical form: colored liquid with specific gravity 0.888538.
• High flammability rating: flash point 20°F (−7°C); HMIS flammability 3.
• VOC content: 888 g/L or 7.4 lbs/gallon.

Technical specifications

• Product identity: Reducer T0001 Fast Spray
• Physical state: liquid (coloured)
• Specific gravity: 0.888538
• Boiling point: 171°F
• Vapor density: heavier than air
• Evaporation rate: slower than ether
• VOC content: 888 g/L (7.4 lbs/gallon)
• Flash point: 20°F (−7°C)
• Lower explosive limit (LEL): 1.38% by volume in air (at normal atmospheric temperature and pressure)
• HMIS rating: Health 3, Flammability 3, Reactivity 1
• Recommended application and cure temperature range (topcoat use): 60–75°F (16–24°C)
• Stability: product is stable; hazardous polymerization will not occur
• Incompatible materials: strong oxidizing agents
• Hazardous decomposition products (when heated to decomposition): may produce carbon dioxide and carbon monoxide

Applications and uses

Use in urethane topcoats

• Use in Awlgrip, Awlcraft 2000 and Awlcraft SE topcoats when application and cure temperatures are between 60–75°F (16–24°C).
• At 60–75°F (16–24°C), T0001 keeps the paint film open for good flow and then evaporates fast enough to provide adequate dry and dust-free times.
• Suitable for spray application of urethane topcoats where a fast evaporating reducer is specified.

Use as a primer reducer

• Usually used in Awlgrip, Awlcraft 2000 and Awlcraft SE topcoats.
• Also recommended for use in Quik-Grip Primer.
• Also recommended for use in Awlbrite Quik-Fil Clear.

FAQ

1. What is the main function of Awlgrip TOPCOAT SPRAY FAST REDUCER (T0001)?

   It is a fast evaporating reducer designed for spray-applied urethane topcoats, helping to balance flow, leveling, and drying performance within the recommended temperature range.

2. Which coating systems is T0001 designed to work with?

   T0001 is used in Awlgrip, Awlcraft 2000 and Awlcraft SE topcoats and is also recommended for Quik-Grip Primer and Awlbrite Quik-Fil Clear.

3. At what temperatures should T0001 be used for topcoats?

   Use T0001 when application and cure temperatures are between 60–75°F (16–24°C).

4. How does T0001 affect the paint film during application?

   In the specified temperature range, it keeps the paint film open long enough to promote good flow and then evaporates quickly enough to achieve adequate dry and dust-free times.

5. What is the VOC content of T0001?

   The VOC content is 888 g/L or 7.4 lbs/gallon.

6. Is T0001 flammable?

   Yes. It is an extremely flammable liquid and vapor with a flash point of 20°F (−7°C). Vapors may cause flash fire and may form explosive mixtures with air.

7. What are the main health hazards associated with this reducer?

   It is harmful if inhaled or swallowed, causes nose, throat and skin irritation, and carries a risk of serious eye damage. Vapors may affect the brain or nervous system, causing dizziness, headache or nausea.

8. Can T0001 be mixed with other Awlgrip reducers?

   All listed reducers for Awlgrip, Awlcraft 2000 and Awlcraft SE topcoats can be blended with each other in any ratio to fine tune flow and evaporation rates.

9. What reduction levels are typical for Awlgrip and Awlcraft 2000 topcoats?

   Most Awlgrip and Awlcraft 2000 topcoats recommend up to 25 percent reduction, calculated from the combined total of base and converter components.

10. Is this product intended for professional or consumer use?

    The documentation specifies that it is for professional use only.

Section 14 – Transportation information

• DOT proper shipping name (domestic surface transportation): PAINT RELATED MATERIAL
• DOT hazard class: 3
• UN / NA number: UN 1263
• DOT packing group: II
• CERCLA / DOT reportable quantity (RQ): 1976 gallons / 14624 lbs
• IMDG proper shipping name (ocean transportation): PAINT RELATED MATERIAL
• IMDG hazard class: 3.2 – Intermediate flashpoint flammable liquids
• IMDG packing group: II
• IMDG UN number: UN 1263

Section 8 – Individual protection measures

Respiratory protection

• Select respiratory equipment to provide protection from the ingredients listed in the hazardous ingredient information.
• Ensure fresh air entry during application and drying.
• If eye watering, headache or dizziness occur, or if air monitoring shows dust, vapor or mist levels above applicable limits, wear an appropriate, properly fitted NIOSH-approved respirator during and after application.
• Follow the respirator manufacturer’s directions for respirator use.

Eye and face protection

• Avoid contact with eyes.
• Depending on site-specific conditions, use safety glasses, chemical goggles and/or head and face protection to prevent contact.
• Protective eye and face equipment must be thoroughly cleaned or discarded after each use.

Skin and hand protection

• Protective equipment should be selected to prevent exposure to the chemicals listed for this product.
• Depending on site-specific conditions, use protective gloves, apron, boots, and head and face protection to avoid skin contact.
• All protective equipment must be thoroughly cleaned or discarded after each use.

Hygiene and workplace practices

• Emergency eye wash fountains and safety showers should be available in the immediate vicinity of any potential exposure.
• Use good personal hygiene practices, including washing hands before eating, drinking or using toilet facilities.
• Promptly remove soiled clothing and wash thoroughly before reuse.
• Shower after work using plenty of soap and water.
• Prevent build-up of vapors by opening windows and doors to achieve cross-ventilation.