What is GRIPTEX ANTI-SLIP ADDITIVE and why choose it?
GRIPTEX ANTI-SLIP ADDITIVE by Awlgrip is a polymer bead aggregate designed to create non-skid deck and step areas when mixed with any Awlgrip topcoat. Supplied as an aggregate/abrasive grit, it can be applied either by broadcasting into a tacky topcoat or by spraying when pre-mixed with the coating. With 100% volume solids, zero VOC as supplied and a simple mixing ratio for spray use, it is a practical solution for professional and industrial applications where durable, slip-resistant surfaces are required.
Main features
- Dedicated non-skid aggregate: Polymer bead particles formulated to generate effective non-skid textures on decks, steps and other walking surfaces when combined with Awlgrip topcoats.
- Multiple texture grades:
- GRIPTEX Non-Skid Particles – Fine (O73012)
- GRIPTEX Non-Skid Particles – Coarse (O73013)
- GRIPTEX Non-Skid Particles – Extra Coarse (O73237)
- High solids, low emissions: 100% volume solids and 0 g/l VOC as supplied (without reducer), helping to minimise solvent emissions from the additive itself.
- Flexible application methods: Can be broadcast onto a still-tacky Awlgrip/Awlcraft 2000 topcoat (Broadcast-Shaker Method) or sprayed when mixed into the topcoat using appropriate spray equipment.
- Supplied for professional and industrial use: Identified uses include professional and industrial applications, with all other uses advised against.
- Non-classified for health and environment: Not classified as hazardous under Regulation (EC) 1272/2008 and not classified as hazardous to the environment when assessed by the CLP summation method.
- Stable and non-reactive in normal use: Stable mixture with no expected hazardous reactions or decomposition products under recommended storage and handling conditions.
Technical specifications
- Product type: Polymer bead aggregate / abrasive grit non-skid additive
- Intended use: To provide non-skid deck and step areas when mixed with any Awlgrip topcoat
- Volume solids: 100%
- VOC (as supplied, without reducer): 0 g/l
- Available pack sizes:
- 1 quart – approximately 1 lb (0.44 kg)
- 1 gallon – approximately 4 lb (1.8 kg)
- Product codes:
- Fine: O73012
- Coarse: O73013
- Extra Coarse: O73237
- Physical properties (Fine O73012):
- Physical state: Solid
- Colour: White
- Odour: Mild
- Density: 0.93 g/cm³ (DIN EN ISO 2811-1)
- Solubility in cold water: Not soluble (OECD TG 105)
- Flash point: 232°C (449.6°F), closed cup (Pensky-Martens)
- Viscosity (kinematic): 1074 mm²/s at room temperature; 999 mm²/s at 40°C (DIN EN ISO 3219)
- Percentage of particles with aerodynamic diameter ≤ 10 µm: 0
- Chemical stability: Product is stable under normal storage and use. No specific conditions to avoid or incompatible materials identified.
Mixing and application data
- Spray application mixing ratio: Add 8–10 oz (227–284 g) by weight of GRIPTEX Non-Skid Particles per mixed gallon (3.785 l) of colour base and converter (Awlgrip or Awlcraft 2000 topcoat).
- Application methods:
- Broadcast-Shaker Method: Apply a light, smooth coat of Awlgrip/Awlcraft 2000 topcoat by spray, brush or roller. After 10–20 minutes, when the surface is slightly dry but still sticky, sprinkle dry GRIPTEX particles uniformly using a shaker or punctured container lid. Allow to dry 12–16 hours, remove loose excess particles, repeat if needed and seal with 1–2 coats of Awlgrip/Awlcraft 2000 topcoat.
- Spray Method: Mix GRIPTEX into the topcoat and apply using a siphon gun or pressure pot with agitator and a minimum 0.070 inch fluid tip. Hold the gun well off the surface and spray in continuous passes beginning and ending on masking paper so that a light, dry coat falls onto the surface. Finish with a sealing coat of Awlgrip/Awlcraft 2000 topcoat.
- Application equipment notes:
- Use only spray guns with at least 0.070 inch fluid tip.
- Do not use airless or air-assist airless spray equipment.
- Mask non-skid areas and surrounding surfaces carefully to control overspray.
- Test on a small, non-critical area before full-scale application.
- Recommended temperature range:
- Do not apply to surfaces warmer than 40°C (105°F) or colder than 15°C (59°F).
- Do not attempt to cure products at temperatures below 13°C (55°F).
Surface preparation guidelines
- GRIPTEX is an additive; follow the primary Awlgrip or Awlcraft 2000 product instructions for full surface preparation.
- Previously painted surfaces must be tested for compatibility before application.
- Existing gelcoat non-skid areas should be thoroughly cleaned and abraded using Scotchbrite, water, abrasive cleaners and stiff brushes.
- After sanding, use a stiff bristle brush wrapped in clean cotton cloth to scrub the surface and remove residues from grooves and valleys. Change cloths frequently.
- Rinse with fresh water, allow to dry, then wipe down with the appropriate Awlgrip wipe-down solvent or surface cleaner.
- Priming surfaces before Awlgrip or Awlcraft 2000 topcoats is noted as improving long-term performance, even on small jobs.
Applications and use cases
- Non-skid decks: Creation or refurbishment of non-skid deck areas where a slip-resistant Awlgrip or Awlcraft 2000 finish is required.
- Steps and walkways: Enhancing traction on steps and designated walking paths finished with Awlgrip topcoats.
- Professional and industrial surfaces: Any professional or industrial setting where Awlgrip topcoats are used and a non-skid surface is required, within the identified uses of the product.
FAQ – GRIPTEX ANTI-SLIP ADDITIVE
-
What type of product is GRIPTEX ANTI-SLIP ADDITIVE?
It is a polymer bead aggregate supplied as an aggregate/abrasive grit, designed to be added to Awlgrip topcoats to produce non-skid surfaces.
-
Which Awlgrip products can I use GRIPTEX with?
It is intended for use with Awlgrip and Awlcraft 2000 topcoats, either sprayed in mixture with the coating or broadcast into a tacky topcoat film.
-
How much GRIPTEX should I add for spray application?
Add 8–10 oz (227–284 g) of GRIPTEX Non-Skid Particles by weight to each mixed gallon (3.785 litres) of colour base and converter.
-
Can I use GRIPTEX with airless spray equipment?
No. The documentation clearly states that airless and air-assist airless spray guns must not be used with GRIPTEX particles.
-
What are the recommended temperatures for application and curing?
Do not apply coatings containing GRIPTEX to surfaces warmer than 40°C (105°F) or colder than 15°C (59°F), and do not attempt to cure products below 13°C (55°F).
-
Is GRIPTEX classified as a hazardous product?
No. According to Regulation (EC) 1272/2008, GRIPTEX Fine Non-Skid O73012 is not classified as hazardous, and no significant health or environmental hazards are identified.
-
How should I prepare existing gelcoat non-skid areas?
Thoroughly clean and abrade with Scotchbrite, water, abrasive cleaners and stiff brushes, then rinse, dry and wipe with the recommended Awlgrip surface cleaner before coating.
-
Can GRIPTEX be used for any application?
No. The product is identified for professional and industrial use; all other uses are advised against.
-
How do I dispose of unused product or empty containers?
Waste generation should be minimised. Dispose of surplus product and non-recyclable material via a licensed waste contractor and in line with all applicable regulations. Empty containers should be scrapped or reconditioned and handled according to local or national rules.
-
Is GRIPTEX harmful to the environment?
The mixture is not classified as hazardous to the environment, but releases to drains and watercourses must be avoided.
Section 14 – Transport information
- UN number / ID number (ADR/RID, IMDG, IATA): Not regulated.
- UN proper shipping name: Not regulated.
- Transport hazard class(es): Not regulated.
- Packing group: Not regulated.
- Environmental hazards: No.
- Transport in bulk according to IMO instruments: Not applicable.
- Special precautions for user: For transport within the user’s premises, always transport in closed containers that are upright and secure. Ensure that personnel transporting the product know what to do in the event of an accident or spillage.
Section 8 – Personal protective measures
The following personal protection and exposure control measures are recommended when handling GRIPTEX FINE NON-SKID O73012, particularly in professional or industrial environments:
- Engineering controls: Good general ventilation is usually sufficient to control airborne contaminants. Where applicable, local exhaust ventilation or additional engineering controls may be required.
- Hygiene measures:
- Wash hands, forearms and face thoroughly after handling, before eating, smoking or using the lavatory and at the end of the working period.
- Use appropriate techniques to remove potentially contaminated clothing and wash contaminated garments before reuse.
- Ensure that eyewash stations and safety showers are close to the workstation.
- Eye and face protection: Use safety eyewear complying with an approved standard when there is a risk of exposure to liquid splashes, mists, gases or dusts. If contact is possible, safety glasses with side shields are recommended unless a higher level of protection is indicated by risk assessment.
- Hand protection:
- Wear chemical-resistant, impervious gloves complying with an approved standard when handling the product, if indicated by risk assessment.
- For all exposure types, gloves with protection class 2 or higher (breakthrough time > 30 minutes according to EN374) are recommended.
- Recommended glove material: nitrile, thickness ≥ 0.12 mm.
- Replace gloves regularly and whenever signs of damage appear. Glove performance can be reduced by physical or chemical damage and poor maintenance.
- Body protection: Select personal protective clothing based on the task and associated risks. Clothing should be approved by a specialist before handling the product.
- Other skin protection: Select suitable footwear and any additional skin protection measures based on the task and risks, with specialist approval before use.
- Respiratory protection:
- Where ventilation is insufficient or exposure levels may be elevated, select a respirator that meets appropriate standards or certifications.
- Respirators must be used within a formal respiratory protection programme to ensure correct fitting and training.
- Dry sanding, flame cutting or welding of dry paint films containing GRIPTEX will generate dust and/or hazardous fumes; wet sanding or flatting should be used wherever possible. If exposure cannot be controlled by ventilation, use approved/certified disposable particulate dust masks.
- Environmental exposure controls: Check emissions from ventilation or process equipment to ensure compliance with environmental protection legislation. Fume scrubbers, filters or engineering modifications may be required to reduce emissions.
*Contenido generado por IA
