THINNER GTA 007

What is THINNER GTA 007 and why choose it?

THINNER GTA 007 by International Marina is a professional-grade solvent designed for thinning and cleaning marine and industrial coatings. It is typically used with selected International antifoulings, primers and topcoats to optimise application and flow, and to clean application equipment after use. Based mainly on xylene and ethyl benzene, it combines strong solvency power with controlled evaporation for a smooth finish. Some technical details are derived from safety data sources and may not be fully verified; for critical projects, always cross-check with the official technical datasheet from International.

Main features

• Dedicated thinner for International coatings: Formulated for use with specific International marine paints, including certain antifoulings and specialty coatings.
• Improves application and finish: Helps adjust viscosity for airless spray and other professional application methods, promoting uniform film build and appearance.
• Effective equipment cleaner: Suitable for flushing and cleaning spray lines, guns, brushes and rollers immediately after use.
• High solvency aromatic blend: Mixture predominantly containing xylene with ethyl benzene for strong dissolving power on compatible coatings.
• Liquid, flammable product: Classified as a flammable liquid, Category 3, requiring careful handling, storage and transport.
• Professional use: Intended for shipyards, marine service companies and industrial applicators familiar with solvent-borne coatings and relevant safety regulations.

Technical specifications

Some of the following values are taken from an English Safety Data Sheet for INTERNATIONAL THINNER (GTA007 / T-5) and may vary slightly depending on region and formulation. Treat them as indicative only and confirm against the manufacturer’s official documentation for your market.

• Product type: Solvent / thinner for paints and coatings
• Typical composition (approximate):
  • Xylene: about 65–85 % (mixture of isomers)
  • Ethyl benzene: about 10–30 %
• Physical state: Liquid
• Appearance: Coloured liquid
• Relative density (20 °C, approx.): about 0.86
• Boiling point (approx.): around 137 °C
• Flash point (approx.): around 26 °C (closed cup)
• Vapour density: Heavier than air
• Primary solvents: Aromatic hydrocarbons
• Intended use: Thinner and cleaner for compatible International coatings (marine and protective)
• GHS hazard classification (indicative):
  • Flammable liquid, Category 3
  • Acute toxicity (dermal), Category 4
  • Skin irritation, Category 2
  • Eye irritation, Category 2
  • Specific target organ toxicity (repeated exposure), Category 2
• Typical hazard statements (summary): Flammable liquid and vapour; harmful in contact with skin; causes skin and serious eye irritation; may cause damage to organs through prolonged or repeated exposure.

Applications and use cases

• Marine antifouling systems: Used as a dedicated thinner for certain International antifouling coatings, where a small percentage may be added to adjust application viscosity as per paint datasheet instructions.
• Primers and intermediates: In some systems, GTA 007 is recommended for thinning or cleaning when applying specific primers or tie coats in shipbuilding and repair.
• Topcoats and specialty coatings: May be specified for selected solvent-borne finishes (for example, certain heat-resistant or protective topcoats) manufactured by International.
• Equipment cleaning: Effective for flushing airless spray equipment, hoses and guns immediately after application of compatible coatings, as well as cleaning brushes and rollers before the paint cures.
• Shipyards and industrial facilities: Commonly used in dry docks, refit yards and industrial maintenance projects where International systems are specified.

Always follow the paint manufacturer’s instructions regarding which products can be thinned with GTA 007, the maximum thinning ratio, and any local environmental restrictions on solvent use. If this information is not available in the product label, request the official technical datasheet from International.

FAQ – THINNER GTA 007

1. What is THINNER GTA 007 used for?

   THINNER GTA 007 is used to adjust the application viscosity of specific International marine and protective coatings, and to clean application equipment after using those products. It should only be used where explicitly recommended by the coating’s technical documentation.

2. Can I use GTA 007 with any paint?

   No. GTA 007 is formulated for particular International coatings, especially some antifoulings and specialised primers or topcoats. Using it with non-compatible products can affect drying, adhesion or performance. Always check the paint manufacturer’s recommendation first.

3. Is THINNER GTA 007 flammable?

   Yes. It is a flammable liquid (Category 3) with a flash point of roughly 26 °C. Keep away from heat, sparks, open flames and hot surfaces, and use only in well-ventilated areas with appropriate explosion-proof equipment where required.

4. What is the main solvent in GTA 007?

   According to an English Safety Data Sheet, GTA 007 is mainly composed of xylene (approximately 65–85 %) with ethyl benzene (approximately 10–30 %). Exact composition can vary by region and batch, so this information should be treated as indicative only.

5. How should I store THINNER GTA 007?

   Store the container tightly closed in a cool, well-ventilated place away from sources of ignition and direct sunlight. Avoid temperatures above those specified by the manufacturer and keep out of reach of unauthorised personnel.

6. Can I use GTA 007 for degreasing surfaces?

   Its primary purpose is thinning and cleaning equipment for compatible coatings, not general-purpose degreasing. For surface preparation, follow the specific surface-cleaning recommendations in the coating system’s technical documentation or use dedicated surface cleaners approved by the manufacturer.

7. Is GTA 007 hazardous to health?

   Yes. It can be harmful in contact with skin, cause skin and eye irritation, and may cause organ damage through prolonged or repeated exposure. Avoid inhalation of vapours and skin or eye contact, and always use suitable personal protective equipment and ventilation.

8. What should I do in case of a spill?

   Evacuate non-essential personnel, eliminate ignition sources, ensure adequate ventilation and contain the spill with non-combustible absorbent materials. Prevent the product from entering drains or waterways. Follow local regulations for collection and disposal, using trained personnel and suitable protective equipment.

9. Where can I find definitive technical data?

   For precise values such as recommended thinning percentages, compatible products and performance data, consult the official technical datasheet and the Safety Data Sheet issued by International or its authorised distributors.

Section 14 – Transport information

The following transport data are taken from a Safety Data Sheet for INTERNATIONAL THINNER (GTA007 / T-5) and are provided as an indicative summary. Regulations and classifications can differ by country and by version of the SDS, so always verify against the latest official documentation for your region.

• UN number: UN 1263
• Proper shipping name: Paint related material
• Transport hazard class: Class 3 (Flammable liquid)
• Packing group: III
• Typical labelling: Flammable liquid, aromatic solvent blend
• General transport considerations:
  • Classified as dangerous goods; transport must comply with ADR/RID, IMDG, IATA or other applicable regulations.
  • Ensure containers are properly closed, upright and secured during transport.
  • Keep away from sources of ignition and incompatible materials (such as strong oxidising agents).
  • Drivers and handlers should be informed of the hazards and emergency measures.

Section 8 – Individual protection measures

This section summarises key recommendations from an English Safety Data Sheet for INTERNATIONAL THINNER (GTA007 / T-5). Actual requirements can vary according to national legislation, workplace risk assessment and specific use conditions.

Engineering controls

• Provide adequate ventilation, especially in confined or enclosed spaces.
• Use local exhaust ventilation where vapour concentrations may approach or exceed occupational exposure limits for xylene and ethyl benzene.

Personal protective equipment (PPE)

• Hand protection: Wear chemical-resistant, impervious gloves compliant with an appropriate standard for organic solvents. Choose glove material and breakthrough time based on supplier data and the duration of contact.
• Eye and face protection: Avoid eye contact. Use safety eyewear that meets an approved standard; where splashes may occur, wear chemical splash goggles. In high-risk situations, additional face protection (face shield) may be required.
• Respiratory protection: Ensure good fresh-air supply during application and drying. If ventilation is insufficient, or if air monitoring indicates vapour concentrations above applicable limits, use a properly fitted respirator suitable for organic vapours, selected and used according to the manufacturer’s instructions and local regulations.
• Skin and body protection: Wear protective clothing resistant to solvent splashes. Where there is risk of ignition from static electricity, use antistatic protective clothing and footwear. Additional PPE (apron, boots, head protection) may be required based on the site-specific risk assessment.

Hygiene measures

• Avoid breathing vapours or spray mist and avoid direct skin and eye contact.
• Do not eat, drink or smoke while using the product.
• Wash hands, forearms and face thoroughly after handling and before breaks or leaving the work area.
• Remove contaminated clothing and protective equipment before entering eating areas; wash contaminated garments before reuse.

*Contenido generado por IA .