EPOXY THINNER D-601

What it is and why choose it

Epifanes Epoxy Thinner D-601 is a clear, solvent-based thinner specifically formulated for use with Epifanes epoxy primers, including Epifanes Epoxy Primer. It is designed to adjust application viscosity for brushing, rolling or spraying and to improve penetration of the mixed epoxy system into substrates such as bare wood and steel. With 100% organic solvent content and high volatility, it enables good flow and leveling, fast drying and a clean, residue-free finish.

Main features

• Dedicated epoxy thinner: Recommended thinner for Epifanes Epoxy Primer (brush, roller and spray application) and for Neosil epoxy primer.
• High solvent strength: Mixture of organic solvents (including pentan-2-one, xylene, 1-methoxy-2-propanol and ethylbenzene) for effective viscosity reduction and surface penetration.
• Fast-evaporating: Boiling range around 101.7 °C and kinematic viscosity of 0.9 mm²/s at 20 °C support quick flash-off and drying.
• Clear liquid: Colourless, characteristic solvent odour, leaves no solid residue (0% solids content).
• High VOC content: 100% organic solvents, VOC content 863.9 g/L.
• Highly flammable: Classified as Flam. Liq. 2; flash point 16 °C and very flammable vapour/air mixtures (lower explosion limit 1.5% v/v, upper approx. 20% v/v).
• Professional-grade formulation: Intended for professional and craft applications (SU22) where controlled thinning of epoxy coating systems is required.

Technical specifications

• Product type: Epoxy thinner / solvent mixture
• Application: Thinner for Epifanes Epoxy Primer and Neosil epoxy primer; for brush, roller and spray applications as indicated on the relevant product information sheet.
• Physical state: Fluid, clear liquid
• Odour: Characteristic solvent odour
• Boiling point: Approx. 101.7 °C (based on pentan-2-one)
• Flash point: 16 °C
• Auto-ignition temperature: Approx. 270 °C (1-methoxy-2-propanol)
• Flammability: Highly flammable liquid and vapour (Flam. Liq. 2)
• Explosion limits: Lower approx. 1.5% v/v; upper approx. 20% v/v (solvent dependent)
• Density: 0.86393 g/cm³ at 20 °C
• Kinematic viscosity: 0.9 mm²/s at 20 °C
• Water solubility: > 20 g/L at 20 °C
• VOC: 100% (863.9 g/L / 7.21 lb/gal)
• Solids content: 0%
• Main components: Pentan-2-one (25–50%), xylene (25–50%), 1-methoxy-2-propanol (10–25%), ethylbenzene (≥2.5–<10%)
• Hazard classification (CLP): Flam. Liq. 2; STOT RE 2; Asp. Tox. 1; Skin Irrit. 2; Eye Irrit. 2; STOT SE 3
• Typical hazard statements: Highly flammable liquid and vapour; may be fatal if swallowed and enters airways; may cause damage to the hearing organs through prolonged or repeated exposure; causes skin and serious eye irritation; may cause respiratory irritation.

Applications and use cases

• Thinning Epifanes Epoxy Primer for brushing/rolling: Used to reduce viscosity of the mixed two-component primer to achieve smooth application and good flow, especially at lower temperatures.
• Thinning for spray application: Added to Epifanes Epoxy Primer prior to conventional or airless spraying, following the thinner ratios indicated for air spray and airless spray.
• Improved penetration on bare substrates: The Epifanes Epoxy Primer sheet specifies that for bare plywood and metals the first coat should be thinned by about 20–25% and applied with a stiff brush to optimise penetration and adhesion; D-601 is the indicated thinner for this purpose.
• Adjustment to job and climate conditions: The thinner ratio is adapted to the temperature of the mixed epoxy product and the working area to balance flow, penetration and solvent release.
• Professional maintenance and repair work: Suitable wherever Epifanes epoxy primers are used for bonding, filling and anti-corrosive priming above and below the waterline on GRP, steel, plywood and aluminium, and where viscosity control is required.

FAQ

1. 1. What is Epifanes Epoxy Thinner D-601 used for?

   It is a solvent mixture formulated to thin Epifanes epoxy primers, such as Epifanes Epoxy Primer and Neosil epoxy primer, for brush, roller or spray application.

2. 2. Can I use D-601 with non-epoxy paints or other brands?

   The documentation specifies its use as thinner for Epifanes epoxy primers. For other products, Consultar ficha técnica del fabricante.

3. 3. How much thinner should I add?

   The Epifanes Epoxy Primer sheet advises adding thinner only after mixing base and curing components. The exact ratio depends on temperature and application method. For penetration on bare wood and steel, the first coat is typically thinned by about 25%.

4. 4. Is Epoxy Thinner D-601 flammable?

   Yes. It is classified as a highly flammable liquid and vapour (Flam. Liq. 2) with a flash point of 16 °C. Keep away from heat, sparks, open flames and hot surfaces and do not smoke.

5. 5. What health hazards are associated with this thinner?

   It may be fatal if swallowed and enters airways, may cause damage to the hearing organs through prolonged or repeated exposure, causes skin and serious eye irritation and may cause respiratory irritation.

6. 6. Do I need ventilation when using this product?

   Yes. It should be used only outdoors or in well-ventilated areas, with good ventilation or exhaust at the workplace to avoid inhaling vapours.

7. 7. How should I store Epifanes Epoxy Thinner D-601?

   Store only in the original, tightly closed container, in a cool, dry and well-ventilated place. Keep away from ignition sources and from other flammable materials.

8. 8. How do I dispose of leftover thinner and empty containers?

   Do not dispose of with household waste or into drains. Waste and uncleaned packaging must be disposed of according to official local regulations under the appropriate waste codes for solvent-containing paint and varnish residues.

9. 9. Is the product hazardous to water?

   Yes. It is classified as water hazard class 2 (hazardous to water). Avoid release to ground water, surface water or sewage systems.

10. 10. Where can I find more detailed safety information?

    More detailed data are available in the official safety data sheet of Epifanes Epoxy Thinner D-601. Consultar ficha técnica del fabricante.

Section 14 – Transport information

• UN number: UN1263
• UN proper shipping name (ADR): 1263 PAINT RELATED MATERIAL (vapour pressure at 50 °C not more than 110 kPa)
• UN proper shipping name (IMDG, IATA): PAINT RELATED MATERIAL
• Transport hazard class: Class 3 – Flammable liquids
• Label: 3
• Packing group: II
• Marine pollutant: No
• Hazard identification number (Kemler code): 33
• EMS: F-E, S-E
• Stowage category (IMDG): B
• ADR limited quantities (LQ): 5 L
• ADR excepted quantities (EQ): Code E2 (maximum 30 ml per inner packaging, 500 ml per outer packaging)
• IMDG limited quantities (LQ): 5 L
• IMDG excepted quantities (EQ): Code E2 (maximum 30 ml per inner packaging, 500 ml per outer packaging)

Section 8 – Individual protection measures

Exposure controls

• Use only in well ventilated areas, with sufficient general or local exhaust.
• Keep away from food, drinks and animal feed. Wash hands before breaks and after work.
• Remove soiled or impregnated clothing immediately and store protective clothing separately.

Personal protective equipment (PPE)

• Respiratory protection:
  • Respiratory protection is recommended.
  • Use filter type AX or an appropriate organic vapour filter.
  • For short or low exposure, a filter device may be used; for intensive or prolonged exposure, use breathing apparatus independent of ambient air (e.g. half-face mask for organic vapours and solvents according to EN140 type A1 or A2).
• Hand protection:
  • Wear protective gloves that are impermeable and resistant to the product.
  • Due to lack of specific testing on the mixture, no single glove material can be recommended; selection must consider breakthrough times, diffusion rates and degradation.
  • For permanent contact up to 15 minutes, butyl rubber (BR) gloves are indicated as suitable.
• Eye and face protection:
  • Wear tightly sealed safety goggles.
• Body protection:
  • Use a protective suit suitable for handling organic solvents.

*Contenido generado por IA