What AWLWASH 2.0 is and why choose it
AWLWASH 2.0 from Awlgrip is a professional liquid cleaner formulated specifically to clean all Awlgrip finishes. It is designed for use on Awlgrip topcoats and other Awlgrip coatings without containing alkalis, acids or abrasives, helping to maintain the appearance of the coating. The product is free rinsing, which helps decrease drying time, and is described as 100% biodegradable and not harmful to the marine environment under applicable regulations, so it can be discharged in wash water within the provisions of MARPOL Annex V.
Main features
- Formulated to clean all Awlgrip finishes.
- Does not contain alkalis, acids or abrasives.
- Free rinsing formulation that reduces drying time.
- Described as 100% biodegradable.
- Not harmful to the marine environment as defined in Regulation (EC) No. 1272/2008 [CLP/GHS] and can be discharged in wash water within MARPOL Annex V provisions.
- Ready to use by dilution: typical use level is 1 oz (30 ml) of Awlwash 2.0 per gallon of water.
- Can be used in higher concentration, including full strength, for stubborn stains (with increased rinsing).
- Recommended weekly washing to prevent dirt build-up on Awlgrip finishes.
- Optimal application and ambient temperature between 18 °C and 35 °C, with permitted ambient range from 13 °C to 41 °C.
- Product as supplied has theoretical VOC content of 0 g/L.
Technical specifications
- Product type: Liquid cleaner for Awlgrip finishes (mixture).
- Volume solids: 15%.
- Available pack size: 1 US gallon (3.785 litres).
- Product code / base: O73235.
- Typical shelf life: 2 years (according to product data sheet).
- Density: approximately 1.021 g/cm³.
- Colour: colourless.
- Appearance: liquid.
- Odour: faint odour.
- pH (as supplied): not applicable / not specified in data sheet.
- Boiling point: approx. 100 °C.
- Flash point: closed cup 101 °C (Pensky-Martens).
- Viscosity: kinematic approx. 294–300 mm²/s (room temperature to 40 °C).
- VOC (product as supplied): 0 g/L (0 lb/gal).
Applications and use cases
Intended uses
- Routine washing and maintenance cleaning of Awlgrip finishes on professional and industrial applications.
- Cleaning of Awlgrip coated surfaces where protection of the coating from alkalis, acids and abrasives is required.
- Suitable for regular maintenance; manufacturer recommends washing once a week to prevent dirt build-up.
Application instructions (from technical data sheet)
- Rinse the Awlgrip surface thoroughly with water before washing.
- Prepare a cleaning solution using 1 oz (30 ml) of Awlwash 2.0 per gallon of water.
- Wash the surface while it is still wet from the initial rinse, using a soft, non-abrasive applicator.
- Do not allow Awlwash 2.0 to dry on the surface before rinsing.
- On large areas, wash small sections at a time to keep the surface wet.
- Rinse thoroughly after washing.
- When finished, wipe the surface with a soft cotton towel or chamois to help prevent water spots.
- If water spots are an issue, the data sheet notes that they are caused by organic and inorganic impurities in the water; if allowed to air-dry, these residues can mark the paint. They can be removed with Awlgrip AWLCARE Protective Polymer Sealer (product reference 73240).
- For stubborn stains, a higher concentration of Awlwash 2.0 may be used. Very stubborn areas may require use at full strength and will require increased rinsing.
Recommended temperature conditions
- Optimal surface/ambient temperature: 18 °C (60 °F) to 35 °C (95 °F).
- Ambient temperature should be between 13 °C (55 °F) and 41 °C (105 °F).
- Do not apply to surfaces less than 3 °C above the dew point or to surfaces warmer than 41 °C.
FAQ
1. What surfaces is AWLWASH 2.0 designed for?
It is formulated to clean all Awlgrip finishes. The product data sheet and safety data sheet describe it as intended for professional and industrial use on Awlgrip coatings.
2. Does AWLWASH 2.0 contain harsh chemicals like alkalis, acids or abrasives?
No. The technical documentation specifies that Awlwash 2.0 does not contain alkalis, acids or abrasives.
3. What is the recommended dilution ratio?
The application data states 1 oz (30 ml) of Awlwash 2.0 per gallon of water for routine cleaning.
4. Can I use it undiluted for heavy staining?
Yes, for stubborn stains the technical sheet indicates that higher concentrations may be required and some stains may require Awlwash 2.0 to be used at full strength. Higher concentrations need more thorough rinsing.
5. How often should Awlgrip surfaces be washed with this product?
The manufacturer recommends washing the surface once a week to prevent dirt build-up.
6. Is AWLWASH 2.0 safe for the marine environment?
According to the product data sheet, Awlwash 2.0 is not harmful to the marine environment as defined in Regulation (EC) No. 1272/2008 [CLP/GHS] and can be discharged in wash water within the provisions of MARPOL Annex V [Resolution MEPC.295(71)].
7. Does the product contain VOCs?
The VOC information provided indicates that, as supplied and without reducer, Awlwash 2.0 has a theoretical VOC content of 0 g/L.
8. What hazards are associated with this cleaner?
The safety data sheets classify the mixture as causing serious eye damage (Eye Dam. 1, H318). They also state that it contains CMIT/MIT (3:1), which may produce an allergic skin reaction. Appropriate protective equipment must be used.
9. Is AWLWASH 2.0 for consumer or professional use?
The safety data sheets specify that the product is for professional use only.
10. What is the shelf life?
The product data sheet indicates a typical shelf life of 2 years when stored correctly in the original sealed container.
Section 14 – Transport information
According to the transport information sections of the safety data sheets:
- ADR/RID: Not regulated.
- IMDG: Not regulated.
- IATA: Not regulated.
- UN number / ID number: Not regulated (no UN number assigned in ADR/RID, IMDG or IATA tables provided).
- UN proper shipping name: Not specified, as the product is not regulated for transport under these codes.
- Transport hazard class(es): Not applicable.
- Packing group: Not applicable.
- Environmental hazards (IMDG / IATA): Listed as “No”.
Special precautions for user: for transport within the user’s premises, the SDS recommends always transporting in closed containers that are upright and secure, and ensuring that persons transporting the product know what to do in the event of an accident or spillage.
Transport in bulk according to IMO instruments / MARPOL Annex II and IBC Code: not applicable / not available for this product.
Section 8 – Individual protection measures
The safety data sheets provide the following guidance on exposure control and personal protective equipment when handling AWLWASH 2.0 in professional or industrial environments:
General hygiene measures
- Eating, drinking and smoking should be prohibited where the product is handled, stored or processed.
- Wash hands, forearms and face thoroughly after handling chemical products and before eating, smoking or using the lavatory.
- Remove contaminated clothing and protective equipment before entering eating areas.
- Wash contaminated clothing before reuse.
- Ensure that eyewash stations and safety showers are close to the work area.
Eye and face protection
- Wear eye or face protection as required by the hazard classification Eye Dam. 1, H318.
- The SDS recommends chemical splash goggles and/or a face shield that comply with approved standards (such as EN 166) when there is a risk of exposure to liquid splashes, mists, gases or dusts.
Hand protection
- Use chemical-resistant, impervious gloves complying with an approved standard (for example EN 374) whenever handling the product if a risk assessment indicates this is necessary.
- For prolonged or frequently repeated contact, gloves with protection class 6 (breakthrough time greater than 480 minutes according to EN 374) are recommended; examples given include Viton or nitrile gloves with thickness around 0.38 mm.
- For brief contact, gloves with protection class 2 or higher (breakthrough time greater than 30 minutes according to EN 374) are recommended; examples include nitrile gloves with thickness around 0.12 mm.
- Gloves should be replaced regularly and whenever there are signs of damage or deterioration.
Skin and body protection
- Wear suitable protective clothing selected according to the task and the risks involved, and approved by a specialist (referenced to EN ISO 13688 in the Spanish SDS).
- Use appropriate footwear and any additional skin protection measures based on the risk assessment.
- Barrier creams may help protect exposed areas of skin but should not be applied after exposure has occurred.
Respiratory protection
- If ventilation is inadequate or if a risk assessment indicates it is necessary, use a properly fitted air-purifying or air-supplied respirator that complies with relevant standards (for example EN 529 guidance for selection).
- The respirator must be selected based on actual or expected exposure levels and the hazard characteristics of the product, and must form part of an appropriate respiratory protection program.
Environmental exposure controls
- Emissions from ventilation or work process equipment should be checked to ensure compliance with environmental protection legislation.
- Where necessary, use fume scrubbers, filters or engineering modifications to reduce emissions to acceptable levels.
*Contenido generado por IA
