TOPCOAT SPRAY FAST EVAP. REDUCER T0002

What is Awlgrip T0002 Topcoat Spray Fast Evaporating Reducer and why choose it

Awlgrip T0002 Topcoat Spray Fast Evaporating Reducer is a fast-evaporation solvent blend designed for use with Awlgrip, Awlcraft 2000 and Awlcraft SE polyurethane topcoats. It optimizes spray application at cooler temperatures, helps maintain an open paint film for proper flow, and then evaporates rapidly to deliver suitable dry and dust-free times. In addition, T0002 functions as an effective cleaner for spray guns and application equipment.

This product is particularly suited to controlled marine and industrial finishing environments where consistent film appearance, correct drying behavior and clean application equipment are critical.

Main features

• Fast‑evaporating spray reducer specifically formulated for Awlgrip, Awlcraft 2000 and Awlcraft SE topcoats.
• Ideal temperature window for application and cure between 55–70°F (13–21°C).
• Keeps paint film open long enough to ensure proper flow and leveling, while still providing adequate dry and dust‑free times.
• Dual‑purpose product: can also be used as an equipment and spray gun cleaner.
• Supports flattened finishes: recommended reducer for topcoats flattened with G3013 Flattening Agent and for G2002 Awlgrip Flat Black to promote best finish development.
• Can be combined with T0005 at higher temperatures above 90°F (32°C) to help combat solvent popping.
• High-solvent strength with a VOC content of approximately 806 g/L (6.7 lb/gal).
• Flammable liquid with a low flash point; requires appropriate storage, handling and personal protection.

Technical characteristics

Composition and regulatory information

• Main component: Butanone (CAS 78-93-3), 100% by weight.
• RCRA status (Butanone): 100.
• TSCA: All ingredients are listed on, or are not required to be listed on, the TSCA Inventory.
• WHMIS classification: Consultar ficha técnica del fabricante.

Physical and chemical properties

• Physical state: Coloured liquid.
• Specific gravity: 0.803.
• Boiling point: 175°F.
• Vapor density: Heavier than air.
• Evaporation rate: Slower than ether.
• VOC content: 806 g/L (6.7 lb/gal) for T0002 reducer.
• pH: No established limit.

Flammability and hazard ratings

• Flash point: 23°F (−5°C).
• DOT hazard class: 3 (flammable liquid).
• IMDG hazard class: 3.2 (intermediate flashpoint flammable liquids).
• Lower explosive limit (LEL): 2% by volume in air (at normal conditions).
• HMIS rating: Health 2, Flammability 3, Reactivity 0.

Stability and reactivity

• Chemical stability: Product is stable; hazardous polymerization will not occur.
• Sensitivity to mechanical impact: Not sensitive.
• Incompatible materials: Strong oxidizing agents.
• Hazardous decomposition products: Carbon dioxide and carbon monoxide may be generated when heated to decomposition (for example, during welding).

Storage conditions

• Recommended storage temperature: Between 32°F and 120°F.
• Storage precautions: Keep away from heat, sparks, open flames and all ignition sources. Do not smoke in storage or application areas. Close container after each use and prevent vapor build‑up through adequate ventilation.

Applications and use cases

As a spray reducer for polyurethane topcoats

• Designed for use in Awlgrip, Awlcraft 2000 and Awlcraft SE spray-applied urethane topcoats.
• Recommended when application and cure temperatures are 55–70°F (13–21°C).
• Within this temperature range, T0002 will keep the paint film open sufficiently for good flow and leveling, while evaporating quickly enough to achieve appropriate dry and dust-free times.
• Used as the reducer in flattened topcoats (with G3013 Flattening Agent) and in Awlgrip Flat Black G2002 for optimal finish appearance.

Use in hot conditions with other reducers

• At temperatures above 90°F (32°C), T0002 can be used in combination with T0005 Hot Weather Reducer.
• The combination is used to combat solvent popping and to fine tune evaporation rate and film formation in demanding conditions.

Equipment and spray gun cleaning

• T0002 is described as an excellent gun and equipment cleaner.
• Suitable for flushing and cleaning spray equipment after the application of compatible Awlgrip, Awlcraft 2000 and Awlcraft SE topcoats.
• Ensure all relevant safety and handling precautions from the safety data sheet are followed during cleaning and waste disposal.

FAQ – Awlgrip T0002 Fast Evaporating Reducer

1. 1. What coatings is T0002 designed for?

   T0002 is intended for use in Awlgrip, Awlcraft 2000 and Awlcraft SE urethane topcoats, and as a cleaning solvent for associated spray equipment.

2. 2. What is the recommended temperature range for using T0002 as a reducer?

   Use T0002 when application and cure temperatures are between 55–70°F (13–21°C).

3. 3. Can T0002 be blended with other Awlgrip reducers?

   Yes. All listed Awlgrip, Awlcraft 2000 and Awlcraft SE topcoat reducers can be blended with each other in any ratio to fine tune flow and evaporation rates. T0002 may also be combined with T0005 at higher temperatures to combat solvent popping.

4. 4. Is T0002 suitable for brushing applications?

   The product information describes T0002 as a spray reducer and equipment cleaner. For brushing or rolling applications, other designated brushing reducers such as T0031 are referenced in the general reducer guide.

5. 5. What is the VOC content of T0002?

   T0002 has a VOC of approximately 806 g/L or 6.7 lb/gal.

6. 6. What are the main health hazards associated with T0002?

   Inhalation can cause nose and throat irritation, dizziness, headache or nausea; skin contact can cause irritation and dermatitis; eye contact presents a risk of serious eye damage; ingestion may be harmful and lead to abdominal discomfort and related symptoms.

7. 7. Can T0002 be used for cleaning all types of coatings and equipment?

   The documentation specifies T0002 as an excellent cleaner for guns and equipment used with Awlgrip, Awlcraft 2000 and Awlcraft SE topcoats. Consultar ficha técnica del fabricante for compatibility with other coating systems.

8. 8. How should waste and residues of T0002 be disposed of?

   Waste must be disposed of in accordance with applicable local, state and federal regulations.

9. 9. Is T0002 classified as a carcinogen?

   Butanone, the main component, is not listed as a known or suspected carcinogen by OSHA, NTP or IARC according to the provided data.

10. 10. Is T0002 for professional use only?

    Yes. The safety documentation states that the product is for professional use only and that users must comply with all applicable health and safety regulations.

Section 14 – Transportation information

• DOT (domestic surface transport) proper shipping name: Paint Related Material.
• DOT hazard class: 3.
• UN/NA number: UN 1263.
• DOT packing group: II.
• CERCLA/DOT reportable quantity (RQ): 747 gallons / 5000 lb.
• IMO/IMDG proper shipping name: Paint Related Material.
• IMDG hazard class: 3.2 – Intermediate flashpoint flammable liquids.
• IMDG packing group: II.

Section 8 – Personal protection measures

Respiratory protection

• Select respiratory equipment to protect against exposure to butanone as listed in the safety data.
• Ensure fresh air entry during application and drying.
• If eye irritation, headache, dizziness or air monitoring indicates dust, vapor or mist above applicable limits, wear an appropriate, properly fitted NIOSH‑approved respirator during and after application.
• Follow the respirator manufacturer’s instructions for selection, use and maintenance.

Eye and face protection

• Avoid eye contact.
• Depending on site‑specific conditions, use safety glasses, chemical goggles and/or head and face protection to prevent splashes or vapor contact.
• Protective equipment must be thoroughly cleaned after each use or discarded.

Skin and hand protection

• Use protective gloves and, where necessary, protective clothing such as aprons, boots, and head and face protection to prevent skin contact.
• All protective equipment should be selected based on exposure to butanone and site‑specific conditions of use.
• Thoroughly clean protective equipment after use or discard contaminated items.

Engineering controls and hygiene

• Prevent vapor build‑up by achieving cross‑ventilation, for example by opening windows and doors.
• Provide emergency eye‑wash stations and safety showers in areas where exposure is possible.
• Use good personal hygiene practices: wash hands before eating, drinking or using toilet facilities.
• Promptly remove soiled clothing, wash thoroughly before reuse, and shower after work using plenty of soap and water.