What is Wall Cover Guard and why choose it
Wall Cover Guard by Coverguard is a temporary protective sheeting designed to shield vertical surfaces such as walls and bulkheads during construction, refit and repair work. Made from flame-retardant polyethylene, it helps prevent impact damage, scuffs and contamination on finished surfaces while work is carried out around them. It is suitable for professional contractors, shipyards and refurbishment projects where reliable and reusable surface protection is needed. Some details below are based on publicly available technical information and may not be fully verified for your specific supply; always confirm with the official technical datasheet.
Main features
- Flame-retardant polyethylene sheeting for temporary wall and bulkhead protection.
- Developed specifically for vertical surfaces, derived from the original Floor Cover Guard range.
- Flat sheet finish with one smooth side and one matt side for versatile installation.
- Supplied in long rolls to cover large areas quickly and reduce joint lines.
- Distinctive "Cover Guard Ocean Blue" colour for clear visibility on site.
- Suitable for use in new build, refit and repair projects across marine, construction and industrial environments.
- Can also be used for wrapping, covering and containment of components and furnishings.
Technical specifications
The following data is compiled from publicly available technical documentation for Wall Cover Guard and is indicative only. Values should be verified against the official technical datasheet of the exact product variant supplied.
- Product type: Temporary protective wall and bulkhead covering.
- Material: Flame-retardant polyethylene (PE).
- Material structure: Taffeta flat sheeting, one side smooth, one side matt (approx. 6 mil taffeta construction).
- Colour: Cover Guard Ocean Blue.
- Nominal thickness: approx. 0.15 mm (150 microns) for the Wall Cover Guard grades referenced.
- Typical roll widths: approx. 0.91 m (36 inches) and 1.82 m (72 inches), depending on product code.
- Typical roll length: approx. 137 m.
- Typical roll area: approx. 125 m² to 249 m² (depending on width).
- Typical roll weight: approx. 19 kg to 38 kg (depending on width).
- Intended surfaces: Vertical walls and bulkheads; also used on floors, weather decks and furnishings in some applications.
- Flame performance: Based on published data, selected Wall Cover Guard products have been tested to fire performance standards such as LPS 1207 and various vertical flame tests. Certification status and scope should be checked against the current official certificates, as listings may change over time.
Note: Public certification records indicate that certain Wall Cover Guard product approvals under LPS 1207 were withdrawn as of January 2026. This information is not a complete or definitive statement of compliance. Always consult the latest official technical and certification documents from the manufacturer or certification body before specifying the product in fire-critical applications.
Applications and typical uses
- Protection of finished wall and bulkhead linings during construction or refurbishment.
- Use in shipbuilding, ship repair and offshore projects to protect interior and exterior vertical surfaces.
- Protection of corridors, stairwells and lift lobbies during renovation works.
- Covering and containment for furniture, fixtures and fittings to prevent dust, paint or debris contamination.
- Temporary protection of weather decks and other exposed surfaces when compatible with site methods.
- Long-run wall protection in large commercial or industrial areas thanks to extended roll lengths.
FAQ
-
Is Wall Cover Guard reusable?
Reusability depends on how the material is installed and removed, and the level of soiling or damage during use. In many light-duty applications, sections can be reused if they remain intact and clean, but this is not guaranteed and is not specifically stated in the public data consulted.
-
Can it be used on any wall surface?
Wall Cover Guard is intended for temporary protection of many finished surfaces, but compatibility with specific coatings, wallpapers, laminates or substrates is not fully detailed in the public information. It is advisable to test on a small, inconspicuous area first and follow the manufacturer’s installation guidance.
-
Is Wall Cover Guard fire-approved for all projects?
Some grades have been tested and previously approved to fire standards such as LPS 1207, but public records indicate that certain approvals were withdrawn in 2026. Fire performance and approval status must be verified for the exact product code and your project requirements before use.
-
How is Wall Cover Guard typically installed?
Common practice is to fix the sheeting to walls or bulkheads using suitable tapes or temporary fixings that do not damage the underlying surface. Specific installation instructions, recommended tapes and overlap details are not fully described in the public data and should be obtained from the official documentation.
-
Can it be used outdoors?
Wall Cover Guard is used in marine and industrial environments, including weather-exposed areas in some applications. However, resistance to prolonged UV exposure, wind and weathering is not fully specified in the sources consulted, so outdoor use should be assessed project by project and confirmed with the manufacturer.
-
Is it suitable for high-traffic areas?
The product is designed to help protect surfaces from impact and abrasion, including in busy corridors and work zones. The actual service life will depend on traffic intensity, installation quality and site conditions, which are not exhaustively detailed in the public data.
-
How should offcuts and used material be disposed of?
As a polyethylene-based product, disposal should follow local regulations for plastic waste and any site-specific environmental requirements. No specific disposal method is given in the public documentation reviewed.
Section 14 – Transport information
No specific transport classification, UN number or hazard class details for Wall Cover Guard were found in the public information consulted. As a polyethylene-based protective sheeting, it is generally supplied as non-hazardous rolls for conventional shipment, but this has not been formally verified for all jurisdictions.
For definitive transport classification (including ADR/RID/IMDG/IATA status, if applicable), consult the official safety data sheet (SDS) and current regulations in your country or region.
Section 8 – Personal protective measures
The public technical literature consulted for Wall Cover Guard does not provide detailed personal protective equipment (PPE) requirements for normal handling and installation.
- During standard handling and cutting, follow general good practice on site (for example, suitable work gloves when cutting or handling roll edges, and eye protection if cutting overhead or using cutting tools).
- Ensure good housekeeping to avoid slip or trip hazards when the sheeting is loose on floors or stairs.
- If the product is used in conjunction with adhesives, tapes, solvents or other chemicals, always follow the PPE recommendations of those products’ SDS.
For precise PPE recommendations and exposure controls, always refer to the official safety data sheet issued for the specific Wall Cover Guard product supplied.
This description has been created in basic mode, based on brand and product name plus publicly available information. Some data may not be fully verified or may refer to specific product codes or past certifications. Always consult the official technical and safety documentation from the manufacturer before specification, installation or use.
*Contenido generado por IA
