What is Awlgrip EPOXY SPRAY REDUCER and why choose it?

Awlgrip EPOXY SPRAY REDUCER (OT0006) is a specialised solvent blend designed as the standard epoxy reducer for spray application of Awlgrip epoxy primers and fairing systems. It optimises atomisation, flow and levelling of products such as 545 Epoxy Primer, Awlquik, Sprayable Fairing Compound, Max Cor CF, High Build and Ultra Build Epoxy Primers, and is also recommended for Hullgard Extra Epoxy Primer. Its controlled evaporation rate is tailored to deliver a smooth, even film while maintaining compliant VOC levels for professional marine and industrial coating applications.

Main features

• Standard epoxy spray reducer: Formulated specifically for spray application of Awlgrip epoxy primers and fairing compounds.
• Wide product compatibility: Recommended for 545 Epoxy Primer, Awlquik, Sprayable Fairing Compound, Max Cor CF, High Build, Ultra Build Epoxy Primers and Hullgard Extra Epoxy Primer.
• Balanced evaporation rate: Supports good flow and levelling of the epoxy film while allowing appropriate dry times.
• Clear, low-viscosity liquid: Colorless solvent blend with low kinematic viscosity to aid spraying and atomisation.
• Professional-grade formulation: Classified as a flammable liquid with defined VOC content for controlled, professional use.

Technical specifications

• Product type: Standard epoxy reducer for spray application
• Recommended uses: Reducer for 545 Epoxy Primer, Awlquik, Sprayable Fairing Compound, Max Cor CF, High Build Epoxy Primer, Ultra Build Epoxy Primer; also recommended for Hullgard Extra Epoxy Primer
• Appearance: Colorless liquid
• Odor: Solvent
• Density: 0.854 g/cm³ (DIN EN ISO 2811-1)
• Boiling point (initial): 79°C (174.2°F)
• Flash point: 35°C (95°F), closed cup (Pensky-Martens)
• Physical state: Liquid
• Kinematic viscosity: 2 mm²/s at room temperature and at 40°C (DIN EN ISO 3219)
• Vapor pressure at 20°C: determined by solvent blend (includes butanone 78.7564 mm Hg, toluene 23.17 mm Hg, n-butyl acetate 11.25096 mm Hg)
• VOC content: 850 g/L or 7.1 lb/gal
• Explosive limits (approximate overall range): 1.48% – 13.74% (v/v in air) based on solvent components
• UN number (transport): UN1263
• Proper shipping name: Paint Related Material / Productos para la pintura
• Transport hazard class: 3 (flammable liquid)
• Packing group: III

Applications and use cases

• Epoxy primer reduction for spraying: Use as the standard reducer when spraying 545 Epoxy Primer and Awlquik Primer to adjust viscosity for correct atomisation and film build.
• Fairing and build coats: Suitable for reducing Sprayable Fairing Compound, Max Cor CF, High Build and Ultra Build Epoxy Primers to achieve smoother application and improved flow.
• Hull protection systems: Recommended as reducer for Hullgard Extra Epoxy Primer in spray applications.
• Professional marine refinishing: Intended for professional users in marine yards, shipyards and industrial environments requiring consistent, specification-compliant epoxy undercoat performance.

FAQ – EPOXY SPRAY REDUCER Awlgrip

1. Which Awlgrip products can I use EPOXY SPRAY REDUCER with?

   It is the standard epoxy reducer for spray application of 545 Epoxy Primer, Awlquik, Sprayable Fairing Compound, Max Cor CF, High Build Epoxy Primer and Ultra Build Epoxy Primer, and is also recommended for Hullgard Extra Epoxy Primer.

2. Is this reducer intended for spray, brush, or roller application?

   It is specified as a standard epoxy reducer for spray application of the listed epoxy primers and fairing compounds.

3. What mixing or reduction ratio should I use?

   Mixing ratios and reduction levels must follow the technical data sheet of the specific epoxy primer or fairing compound being used. Consultar ficha técnica del fabricante.

4. What is the VOC content of EPOXY SPRAY REDUCER?

   The VOC content is 850 g/L or 7.1 lb/gal.

5. What is the appearance of the product?

   It is a clear, colorless liquid with a solvent odor.

6. Can this reducer be used with polyurethane or topcoat systems?

   The product is described as a standard epoxy reducer for specific epoxy primers and fairing systems. Use only in the systems and products for which it is recommended. For other coatings, Consultar ficha técnica del fabricante.

7. Is the product flammable?

   Yes. It is classified as a flammable liquid (Flam. Liq. 3) with a flash point of 35°C (95°F). Handle and store away from heat, sparks, open flames and other ignition sources.

8. What health hazards are associated with this reducer?

   It is classified as irritating to skin (Skin Irrit. 2) and causing serious eye damage (Eye Dam. 1). It may cause drowsiness or dizziness (STOT SE 3), may cause damage to organs through prolonged or repeated exposure (STOT RE 2), is suspected of damaging the unborn child (Repr. 2), and may be fatal if swallowed and enters airways (Asp. Tox. 1).

9. Can I use this product in poorly ventilated areas?

   No. It should be used only outdoors or in well-ventilated areas, with appropriate engineering controls and, if required, suitable respiratory protection as indicated in the safety data sheet.

10. Is EPOXY SPRAY REDUCER suitable for consumer use?

    The safety documentation specifies it is for professional and industrial use. Consumer use is listed as a use advised against.

Section 14 – Transport information

• UN number / ID number: UN1263
• UN proper shipping name (ADR/RID): Productos para la pintura
• UN proper shipping name (IMDG/IATA): Paint Related Material
• Transport hazard class: 3 (flammable liquid)
• Packing group: III
• Environmental hazards: Not classified as marine pollutant according to IMDG; no environmental hazard indication in ADR/RID/IATA tables provided.
• ADR/RID tunnel restriction code: D/E
• IMDG emergency schedules: F-E, S-E
• Special precautions for user: Within user premises, always transport in closed containers kept upright and secure. Ensure personnel transporting the product know what to do in case of accident or spillage.
• Transport in bulk according to IMO instruments: Not applicable.

Section 8 – Individual protection measures

Engineering controls

• Use only with adequate ventilation.
• Apply local exhaust ventilation, process enclosures or other engineering controls to keep airborne concentrations below occupational exposure limits and below lower explosive limits.
• Use explosion-proof ventilation equipment.

Personal protective equipment (PPE)

Eye and face protection

• Use safety eyewear complying with an approved standard.
• Where splashes are possible, wear chemical splash goggles and/or face shield.
• A full-face respirator may be required if inhalation hazards and splash risks are both present.

Hand protection

• Wear chemical-resistant, impervious gloves complying with EN374 or equivalent.
• For prolonged or frequently repeated contact, use gloves with protection class 6 (breakthrough time > 480 minutes). Recommended materials: Viton® or nitrile, thickness ≥ 0.38 mm.
• For brief contact, gloves with protection class 2 or higher (breakthrough time > 30 minutes) are recommended. Suggested material: nitrile, thickness ≥ 0.12 mm.
• Replace gloves regularly and immediately if any damage or degradation is observed.

Skin and body protection

• Select protective clothing based on the specific task and associated risks.
• When there is a risk of ignition from static electricity, wear anti-static protective clothing, including anti-static overalls, boots and gloves (refer to EN 1149).
• Use appropriate footwear and any additional skin protection measures approved by a specialist before handling the product.

Respiratory protection

• Based on hazard and exposure potential, select a respirator meeting the appropriate standard or certification.
• Respirators must be used within a respiratory protection program ensuring correct fit and user training.
• Recommended: respirator conforming to EN140 fitted with type A/P2 filter or better.
• Dry sanding, flame cutting or welding of the dry coating film can generate dust and hazardous fumes; wet sanding is preferred. If exposure cannot be controlled by ventilation, use suitable respiratory protection.

Hygiene measures

• Wash hands, forearms and face thoroughly after handling, before eating, drinking or smoking, and at the end of the work shift.
• Remove contaminated clothing and protective equipment before entering eating areas.
• Wash contaminated clothing before reuse; ensure eyewash stations and safety showers are close to the work area.

Environmental exposure controls

• Check emissions from ventilation and process equipment to ensure compliance with environmental protection legislation.
• Where necessary, fit fume scrubbers, filters or modify process equipment to reduce emissions.