LPH-80 TOUCH-UP CUP 70 AND 250 ML

What is the LPH-80 Touch-Up with 70 ml and 250 ml Cups and why choose it

The ANEST IWATA LPH-80 is a low volume, low pressure (LVLP) gravity spray gun designed specifically for spot repair and touch-up work. Supplied with 70 ml and 250 ml gravity cups (PCG-1P-1 and PCG-3P-1), it is ideal for small areas where precise application, reduced overspray and high transfer efficiency are required. With a compact 205 g gun body (without cup), fine atomization at very low pressure and full ATEX conformity for use in potentially explosive atmospheres, it is a professional solution for detailed refinishing and repair work.

Main features

• LVLP technology for spot repair: Designed to atomize efficiently at very low pressure, ideal for local repairs and small panels.
• Gravity cups in two sizes: Compatible with gravity cups PCG-1P-1 (70 ml) and PCG-3P-1 (250 ml) for small touch-ups or larger spot repairs.
• Multiple nozzle options: Available fluid nozzle sizes 0.4, 0.6, 0.8, 1.0 and 1.2 mm to suit a wide range of coating viscosities and applications.
• Compact and lightweight: Gun body weight of 205 g (without cup) helps reduce fatigue during prolonged use.
• Low noise level: Measured noise level of 60.3 dB(A) at 1 m behind the gun and 1.6 m height under test conditions.
• Precise control: Separate controls for fluid adjustment, pattern adjustment and air adjustment to fine-tune spray pattern, material flow and atomizing air.
• Recommended short spray distance: Optimized for 50–150 mm spray distance, ideal for tight areas and detailed refinishing.
• ATEX compliant: Marked II 2 G Ex h IIB T6 Gb X for use in potentially explosive atmospheres according to Directive 2014/34/EU.
• Durable construction: Designed for use with properly filtered compressed air and compatible cleaners; all wear parts are replaceable.

Technical specifications

General data

• Max. working air pressure: 6.8 bar (98 PSI)
• Weight: 205 g (0.45 lbs) without cup
• Noise level (LAeqT): 60.3 dB(A) measured 1 m behind the gun at 1.6 m height (actual noise can exceed 85 dB(A) depending on conditions)
• Air connection: G1/4"
• Fluid connection: G1/8"
• Max. ambient temperature: 5 – 40 °C
• Max. air/fluid temperature: 5 – 43 °C

Models and nozzle sizes

• LPH-80-044G: 0.4 mm nozzle
• LPH-80-064G: 0.6 mm nozzle
• LPH-80-084G: 0.8 mm nozzle
• LPH-80-104G: 1.0 mm nozzle
• LPH-80-124G: 1.2 mm nozzle

Recommended operating conditions

• Suggested atomizing air pressure: 0.5 – 1.0 bar (7 – 14 PSI), providing approx. 0.7 bar (10 PSI) inside the air cap.
• Air hose: For a 12 m hose, minimum internal diameter 8 mm to supply correct air volume.
• Recommended paint viscosity: 12 – 20 seconds with Ford cup #4 (or equivalent), depending on paint and conditions.
• Recommended spray distance: 50 – 150 mm from gun to workpiece.

Gravity cups

• PCG-1P-1 gravity cup: 70 ml, with non-drip device.
• PCG-3P-1 gravity cup: 250 ml, with non-drip device.

Compliance and safety

• ATEX conformity: II 2 G Ex h IIB T6 Gb X +5°C ≤ Ta ≤ +40°C
• Directives and standards: Directive 2014/34/EU, Machinery Directive 2006/42/EC, EN 1127-1:2019, EN ISO 80079-36:2016, EN 1953:2013, EN 614-2:2000+A1:2008 (and related UK standards for UKCA marking).

Applications and use cases

• Automotive spot repair: Local refinishing of small defects, edges, blends and partial panel repairs where tight control and limited overspray are essential.
• General touch-up work: Ideal wherever small areas need precise coating application using a compact LVLP gravity spray gun.
• Detail work in confined areas: Optimized for short working distance (50–150 mm), suitable for components, edges and hard-to-reach surfaces.
• Use with approved liquid coatings: Designed for paints and coatings compatible with aluminium gun bodies; do not use halogenated hydrocarbon solvents listed in the manual.

FAQ

1. What air pressure does the LPH-80 require?

The recommended atomizing air pressure is 0.5–1.0 bar (7–14 PSI), which results in about 0.7 bar (10 PSI) inside the air cap.

2. What cup sizes are compatible with this spray gun?

The gun is designed for use with gravity cups PCG-1P-1 (70 ml) and PCG-3P-1 (250 ml), both with non-drip devices.

3. Which nozzle sizes are available?

Available fluid nozzle diameters are 0.4, 0.6, 0.8, 1.0 and 1.2 mm, matched to corresponding needles.

4. What is the recommended spray distance?

The spray distance should be set as near as possible within the range of 50–150 mm from the gun to the workpiece.

5. How should the gun be cleaned after use?

Immediately after use, especially with two-component paints, flush the fluid passages with a compatible cleaner, then remove the air cap and cup and clean all sections manually with the supplied brush and a cloth. Do not fully immerse the gun in solvent and do not soak the air cap for long periods.

6. Can I use any solvent with this spray gun?

No. Do not use halogenated hydrocarbon solvents such as methyl chloride, dichloromethane, 1.2-dichloroethane, carbon tetrachloride, trichloroethylene, or 1.1.1-trichloroethane, as they can damage the aluminium gun body.

7. What type of air should be supplied to the gun?

Use clean, dry air filtered through an air dryer and air filter. A filter with automatic condensate drain and dryer is recommended.

8. Is the gun suitable for spraying food or chemicals?

No. The manual explicitly states to never use this gun to spray foods or chemicals, to avoid corrosion of fluid passages and health risks.

9. What should I do if the gun does not spray?

Check that the fluid adjustment knob is open, verify that the nozzle tip and non-drip device are not obstructed, and clean them if necessary.

10. What is the maximum working pressure?

The maximum working air pressure is 6.8 bar (98 PSI). This must not be exceeded.

Section 14 – Transport information

Consultar ficha técnica del fabricante.

Section 8 – Personal protective measures

• Always work in a well-ventilated area, preferably in a spray booth.
• Wear suitable eye protection such as safety glasses.
• Use an appropriate mask to protect against inhalation of solvents and overspray.
• Wear protective gloves and clothing to avoid skin contact and irritation.
• Use earplugs or hearing protection if noise levels and working conditions require it (noise can exceed 85 dB(A) depending on the site).

*Contenido generado por IA