What is Epifanes Waterline Paint and why choose it?
Epifanes Waterline Paint is a one-component, high gloss yacht coating specially developed for painting the stripe above the waterline. Based on linseed oil and modified alkyd resin, it is easy to apply in a wide temperature range, offers good gloss retention and provides strong hiding power thanks to its high pigment concentration. It is suitable for new construction and maintenance systems on wood, steel, GRP and aluminium when used with the appropriate primers and topcoats.
Supplied in handy 250 ml cans in several solid colours, this product is ideal wherever only a relatively small quantity of paint is required, such as waterlines and trim areas.
Main features
- One-component, oxidative drying yacht coating for above the waterline.
- High gloss finish with good gloss retention over time.
- High covering power due to high pigment content.
- Easy application by brush or roller over a wide temperature range.
- Suitable for wood, steel, GRP and aluminium in combination with appropriate primer/paint systems.
- Can be applied on existing paint systems, regardless of brand.
- Can also be applied directly to properly prepared GRP surfaces.
- Convenient 250 ml packaging ideal for waterline stripes and smaller areas.
Technical specifications
- Type: Oxidative drying.
- Base: Linseed oil / modified alkyd resin.
- Gloss: High gloss.
- Colours: White, light blue, dark blue, bright red, black, green.
- Density at 20 °C: 0.95 – 1.30 g/cm³ (depending on colour). Additional measured value in SDS: 0.988 g/cm³.
- Viscosity: 40 s ISO-cup 6 mm (kinematic viscosity at 20 °C).
- Solids content: 55 ± 2 vol. % (technical datasheet). SDS value: approx. 70.1 % by weight.
- VOC level (content): approx. 296 g/l (about 29.9 % by weight).
- Recommended film thickness: 70–80 µm wet, corresponding to 40–45 µm dry.
- Theoretical coverage: approx. 14 m²/l at 40 µm dry film thickness.
- Practical coverage: Dependent on substrate condition, application technique, shape of object and working conditions.
- Packaging size: 250 ml.
- Shelf life: Approx. 3 years in closed, unopened container stored dry between 5–30 °C.
- Drying times at 45 µm dry film thickness and 65% RH:
- 10 °C: Dust dry 8 h; sandable/recoatable 48 h.
- 15 °C: Dust dry 6 h; sandable/recoatable 36 h.
- 20 °C: Dust dry 4 h; sandable/recoatable 24 h.
- 25 °C: Dust dry 2 h; sandable/recoatable 20 h.
- Thinner for brushing: Epifanes Brushthinner for Paint & Varnish or good quality white spirit.
- General thinning: Thinning ratio depends on product temperature and working conditions. Over-thinning must be avoided.
- Flash point: approx. 40 °C.
- Explosion limits (solvent phase): Lower 0.6 vol %, upper 7 vol %.
- Ignition temperature: approx. 240 °C.
Applications and use cases
Recommended field of use
- Painting and renewing waterline stripes above the waterline on yachts and boats.
- Use on new systems on:
- Wood.
- Steel.
- GRP.
- Aluminium.
in combination with suitable Epifanes primers and topcoats.
- Overcoating existing paint systems, regardless of manufacturer, after proper preparation.
- Other small areas where only a small amount of topcoat is needed.
Application conditions
- Substrate temperature: Minimum 8 °C, maximum 30 °C.
- Relative humidity: Minimum 50 %, maximum 85 %.
- Maximum allowed temperature difference between paint and substrate: 3 °C.
- Avoid direct sunlight and strong wind to prevent rapid solvent loss and poor flow.
Application method
- Best applied with a roller or long-haired soft brush.
- Distribute paint evenly and do not re-tip.
- Do not apply wet-on-wet.
- Avoid excessively thick wet films to prevent sagging and extended drying times, especially on horizontal surfaces.
- Between coats, allow sufficient drying, then sand lightly by hand with P400 or Scotch-Brite.
System build-up around the waterline
- Apply the complete primer and topcoat system to the hull and allow to cure thoroughly.
- Tape off the waterline once the underlying system has cured.
- Lightly sand the area to be coated.
- Apply Epifanes Waterline Paint to the prepared stripe.
- Remove masking tape in time to prevent adhesion of the tape to the coating.
The product can also be applied directly onto a GRP surface, provided it is well cleaned and sanded.
Compatibility with other Epifanes products
- Epifanes Mono-urethane Yacht Paint.
- Epifanes Nautiforte Yacht Paint.
- Epifanes Non-skid Deck Coating.
- Epifanes Satin Finish.
- Epifanes Flat Black.
FAQ – Epifanes Waterline Paint
1. On which substrates can I use this paint?
It can be used on wood, steel, GRP and aluminium, in combination with suitable primers and paints. It is also suitable for application over existing paint systems, regardless of brand, after correct preparation.
2. Can I apply it directly on GRP without primer?
Yes, Epifanes Waterline Paint may be applied directly to GRP when the surface is thoroughly cleaned and sanded.
3. What is the theoretical coverage?
The theoretical coverage is approximately 14 m² per litre at 40 µm dry film thickness. Practical coverage depends on substrate condition, application method and environmental conditions.
4. How long should I wait between coats?
At 20 °C and 65 % RH, the paint is dust dry after about 4 hours and sandable/recoatable after approximately 24 hours. At lower temperatures drying and recoating times are longer; at higher temperatures they are shorter.
5. Which thinner should I use?
For brushing, use Epifanes Brushthinner for Paint & Varnish or a good quality white spirit. The exact thinning ratio depends on product temperature and working conditions; over-thinning should be avoided.
6. In what temperature and humidity range should I apply the paint?
Apply between 8–30 °C and 50–85 % relative humidity. Avoid direct sunlight and strong wind to maintain good flow and levelling.
7. How should I prepare the waterline area?
First complete and cure the full hull primer/topcoat system, tape off the waterline, lightly sand the stripe, then apply Epifanes Waterline Paint and remove the masking tape before it adheres strongly.
8. How should I store the product?
Store in tightly closed, unopened containers in a dry place between 5–30 °C. Under these conditions the approximate shelf life is 3 years.
9. Is the product flammable?
Yes. Epifanes Waterline Paint is classified as a flammable liquid (Flam. Liq. 3, H226: flammable liquid and vapour). Keep away from heat, sparks, open flames and hot surfaces and follow all safety recommendations on the label and safety data sheet.
10. Are there any health warnings I should know about?
The mixture may cause an allergic skin reaction (H317) and may cause drowsiness or dizziness (H336). Repeated exposure may cause skin dryness or cracking (EUH066). Contains cobalt carboxylate which can cause an allergic reaction. Always use appropriate personal protective equipment and sufficient ventilation.
Section 14 – Transport information
- UN number / ID number: UN1263.
- UN proper shipping name: PAINT.
- Transport hazard class: Class 3 (flammable liquids), label 3.
- Packing group: III.
- ADR specific data:
- Hazard identification number (Kemler code): 30.
- Transport category: 3.
- Tunnel restriction code: D/E.
- Limited quantities (LQ): 5 L.
- Excepted quantities (EQ): Code E1 (max. 30 ml per inner packaging; 1000 ml per outer packaging).
- Remark: Packaging < 450 L may be exempt as viscous substances according to 2.2.3.1.5.
- IMDG / IATA specific data:
- Class: 3, label 3.
- Packing group: III.
- EMS: F-E, S-E.
- Stowage category: A.
- Limited quantities (LQ): 5 L.
- Excepted quantities (EQ): Code E1 (max. 30 ml per inner packaging; 1000 ml per outer packaging).
- Marine pollutant: No.
- Bulk transport according to IMO instruments: Not applicable.
Section 8 – Personal protective measures
According to the safety data sheet (Section 8), the following personal protection and hygiene measures are recommended when handling Epifanes Waterline Paint:
General hygiene measures
- Immediately remove all soiled or contaminated clothing.
- Wash hands before breaks and at the end of the work period.
Respiratory protection
- Ensure good general ventilation or local exhaust at the workplace.
- For short or low exposure, use a breathing filter device suitable for organic vapours.
- For intensive or prolonged exposure, use respiratory equipment independent of the surrounding air.
- A half-face mask for organic vapours and solvents according to EN140 type A1 or A2 is recommended.
Hand protection
- Wear protective gloves that are impermeable and resistant to the product.
- The exact glove material and breakthrough time must be checked with the glove manufacturer, as resistance depends on several factors.
- For permanent contact up to a maximum of 15 minutes, gloves made of butyl rubber (BR) are indicated.
- For protection against splashes, suitable options include:
- Chloroprene gloves with a thickness > 0.7 mm and penetration time > 60 minutes according to EN374.
- Nitrile rubber gloves with a thickness > 0.3 mm and penetration time > 60 minutes according to EN374.
Eye and face protection
- Wear tightly sealed safety goggles to protect against splashes.
Additional safety information
- The product is classified as a flammable liquid and vapour (Flam. Liq. 3, H226).
- May cause an allergic skin reaction (Skin Sens. 1, H317) and may cause drowsiness or dizziness (STOT SE 3, H336).
- Repeated exposure may cause skin dryness or cracking (EUH066).
- Contains cobalt carboxylate, which can cause an allergic reaction.
*Contenido generado por IA
