600 WIPE DOWN SOLVENT

What is 600 Wipe Down Solvent and why choose it?

600 Wipe Down Solvent from International Náutica is a professional wipe-down solvent designed to remove surface contaminants such as waxes, oils and sanding residues prior to sanding, surface preparation or paint application. Its fast-acting solvent blend helps ensure that substrates are clean and ready for high-quality coatings, reducing the risk of defects caused by contamination.

Main features

• Professional-grade wipe-down solvent specifically formulated for pre-paint cleaning of surfaces.
• Effective removal of waxes, oils and sanding dust when used with the recommended two-cloth cleaning method.
• Low density formulation with a specific gravity of 0.74 and 0% volume solids.
• High VOC content (744 g/L as supplied) suitable for professional applications where strong solvency power is required.
• Available in practical pack sizes of 5 L and 200 L for small jobs or large-scale professional use.
• Long typical shelf life of 3 years when stored correctly.
• Highly flammable liquid and vapour classified as Flam. Liq. 2 (H225).
• Hazardous classification: causes skin irritation (H315), causes serious eye irritation (H319), may be fatal if swallowed and enters airways (H304), very toxic to aquatic life with long lasting effects (H410).

Technical specifications

• Product type: Professional wipe down solvent / thinner.
• Product code: ITA075.
• Appearance: Colorless liquid.
• Odour: Solvent.
• Specific gravity / density: 0.74 (0.745 g/cm³).
• Volume solids: 0%.
• VOC (as supplied): 744 g/L.
• Boiling point (initial): 143°C (289.4°F).
• Flash point: -2°C (28.4°F), closed cup (Pensky-Martens).
• Viscosity (kinematic): 1 mm²/s at room temperature and at 40°C (DIN EN ISO 3219).
• Water solubility: Not soluble in cold water (OECD TG 105).
• Main hazardous component: Naphtha (petroleum), hydrotreated light (≥75 – ≤90%).
• Typical shelf life: 3 years (when stored between 5°C and 35°C in tightly closed containers, away from direct sunlight).
• Unit sizes: 5 L and 200 L.

Applications and use cases

• Pre-sanding cleaning: Removes waxes, oils and residues before sanding to promote consistent abrasion and adhesion.
• Surface preparation prior to coating: Cleans substrates immediately before paint application to minimise contamination-related defects.
• Removal of sanding residues: Helps eliminate dust and residues that can impair the final finish if left on the surface.

Recommended application method

• Initial dust removal: Remove dust using a vacuum or dry compressed air while wiping the surface with dry, clean cotton cloths.
• Two Cloth Cleaning Method:
  1. Soak one clean cotton cloth in 600 Wipe Down Solvent and use it to wet the surface.
  2. Immediately wipe the area with a second, dry cloth to remove contaminants.
  3. Do not allow the solvent to dry on the surface.
  4. Work on small areas so that the second cloth can wipe the surface clean and dry before the solvent evaporates.
  5. Repeat the process until all residue has been removed, changing cloths frequently.
• Important application hint: Using only one set of cloths or a single wet cloth will smear contamination around; any sanding residue left on the surface can impair the finish.
• Compatibility: Do not use 600 Wipe Down Solvent as a thinner or reducer.

FAQ

• Can 600 Wipe Down Solvent be used by consumers?

  The product is intended for professional use. Consumer use is listed as “none” in the safety documentation.

• Is this product suitable as a paint thinner?

  No. The technical data clearly state: do not use 600 Wipe Down Solvent as a thinner or reducer.

• What is the main purpose of 600 Wipe Down Solvent?

  It is designed to remove surface contaminants such as waxes, oils and sanding residues prior to sanding, surface preparation or paint application.

• How should I clean the surface correctly?

  Use the Two Cloth Cleaning Method: one cloth soaked in solvent to wet the surface, followed immediately by a second dry cloth to lift away contaminants, working in small areas and changing cloths regularly.

• What happens if solvent dries on the surface?

  The instructions specify that the solvent must not be allowed to dry on the surface, as this can leave contaminants and residues that may affect the finish.

• How long can I store an unopened container?

  The typical shelf life is 3 years, provided the container is firmly closed and stored between 5°C (41°F) and 35°C (95°F), out of direct sunlight.

• What should I do with leftover product or empty containers?

  Remainders cannot be disposed of through municipal waste or dumped without a permit. Disposal must be arranged in consultation with the relevant authorities, following local and national regulations.

Section 14 – Transport information

• UN number / ID number: UN1263.
• UN proper shipping name: Paint Related Material.
• Transport hazard class: Class 3 (flammable liquid).
• Packing group: II.
• Environmental hazards: Classified as hazardous to the environment; marine pollutant component naphtha (petroleum), hydrotreated light.
• ADR/RID: UN1263, Class 3, Packing group II, special provisions 640 (C), tunnel code (D/E). The environmentally hazardous substance mark is not required for packages ≤5 L or ≤5 kg.
• IMDG: UN1263, Class 3, Packing group II, marine pollutant (naphtha (petroleum), hydrotreated light), emergency schedules F-E, S-E. Marine pollutant mark not required for packages ≤5 L or ≤5 kg.
• IATA: UN1263, Class 3, Packing group II. The environmentally hazardous substance mark may appear if required by other transport regulations.
• Special precautions for user: Within user’s premises, always transport in closed, upright and secure containers. Ensure that persons transporting the product know what to do in the event of an accident or spillage.
• Transport in bulk according to IMO instruments: Not applicable.

Section 8 – Personal protective measures

Exposure controls and engineering measures

• Use only with adequate ventilation and, where necessary, local exhaust ventilation or process enclosures to keep airborne concentrations below occupational exposure limits and below lower explosion limits.
• Use explosion-proof ventilation and electrical equipment.

Hygiene measures

• Wash hands, forearms and face thoroughly after handling and before eating, drinking, smoking or using the lavatory.
• Remove contaminated clothing and protective equipment before entering eating areas; wash contaminated clothing before reuse.
• Ensure that eyewash stations and safety showers are close to the workstation.

Eye and face protection

• Wear safety eyewear complying with an approved standard when risk assessment indicates potential exposure to liquid splashes, mists, gases or dusts.
• If contact is possible, chemical splash goggles are recommended.

Hand protection

• Wear chemical-resistant, impervious gloves that comply with an approved standard whenever handling the product and a risk assessment indicates this is necessary.
• For prolonged or frequently repeated contact, gloves of protection class 6 are recommended (breakthrough time > 480 min according to EN374). Recommended materials: Viton or nitrile, thickness ≥ 0.38 mm.
• For brief contact, gloves of protection class 2 or higher are recommended (breakthrough time > 30 min according to EN374). Recommended material: nitrile, thickness ≥ 0.12 mm.
• Replace gloves regularly and immediately if damaged. The effectiveness of gloves can be reduced by physical or chemical damage or poor maintenance.

Body and skin protection

• Select protective clothing based on the specific task and risks, approved by a specialist before use.
• Where there is a risk of ignition from static electricity, wear anti-static protective clothing, including anti-static overalls, boots and gloves (see EN 1149 for requirements).
• Choose appropriate footwear and any additional skin protection measures depending on the operation and associated risks.

Respiratory protection

• Based on the hazard and potential for exposure, select a respirator that meets the appropriate standard or certification.
• Respirators must be used as part of a respiratory protection program to ensure correct fitting, training and proper use.

Environmental exposure controls

• Check emissions from ventilation systems or process equipment to ensure compliance with environmental protection legislation.
• Where necessary, use fume scrubbers, filters or engineering modifications to reduce emissions to acceptable levels.

Contenido generado por IA