What is AWLGRIP SLOW DRYING BRUSHING REDUCER and why choose it?
AWLGRIP SLOW DRYING BRUSHING REDUCER (code T0031 / OT0031) is a professional-grade thinner designed for use with Awlgrip Topcoats, 545 Epoxy Primer and Awlquik Sanding Surfacer in brush and roller applications. Based on 2-butoxyethyl acetate, it evaporates very slowly to keep the paint film open longer, maximizing flow and leveling while minimizing visible brush marks and roller stipple. It is formulated for professional users who need high-quality finishes on marine and industrial substrates under a wide range of ambient temperatures.
Main features
- Slow-evaporation brushing reducer: Keeps the coating open for extended periods, improving flow and leveling.
- Optimized for Awlgrip systems: Specifically indicated for Awlgrip Topcoats, 545 Epoxy Primer and Awlquik Sanding Surfacer.
- Brush and roller application: Recommended for brush/roller use only; not recommended for spray applications.
- Flexible addition rate: For Awlgrip Topcoats, can be added at 10–33% of the total mixed base and converter volume.
- Wide temperature window: Best results when application and cure temperatures are between 60–90°F (16–32°C), with 70–85°F (21–29°C) as the optimum range.
- Professional-grade formulation: High VOC solvent blend (approx. 940 g/L) for demanding marine and industrial finishing environments.
- Harmful on skin or if inhaled: Classified as Acute Tox. 4 (H312, H332); requires appropriate personal protection and ventilation.
Technical specifications
- Product type: Brushing reducer / thinner
- Primary component: 2-butoxyethyl acetate (≥ 90%)
- Physical state: Liquid
- Color: Colorless
- Odor: Characteristic solvent odor
- Density: approx. 0.939 g/cm³ (DIN EN ISO 2811-1)
- Viscosity (kinematic): approx. 1 mm²/s at room temperature and at 40°C (DIN EN ISO 3219)
- Boiling point: approx. 193°C (379.4°F)
- Flash point: approx. 71°C (159.8°F), closed cup (Pensky-Martens)
- Lower/upper explosion limits (2-butoxyethyl acetate): 1.3% – 6.8% (by volume in air)
- Vapor pressure (20°C): approx. 0.23 mm Hg (0.031 kPa)
- Water solubility: Not soluble in cold water (OECD TG 105)
- Partition coefficient (log Pow) for 2-butoxyethyl acetate: 1.51 (low bioaccumulation potential)
- VOC content (reducer itself): approx. 940 g/L or 7.8 lb/gal
- Application method: Brush or roller
- Use category: Professional/industrial use only
Applications and use cases
Compatible coating systems
- Awlgrip Topcoats: Use as a brushing reducer to improve flow and leveling and to reduce brush marks in brush/roller-applied urethane topcoats.
- 545 Epoxy Primer: Use as the brushing reducer when brushing or rollering 545 Epoxy Primer.
- Awlquik Sanding Surfacer / Awlquik Primer: Recommended brushing reducer for brush/roller application.
Recommended addition and conditions
- Addition rate for Awlgrip Topcoats: 10–33% of the total volume of the mixed color base and converter.
- Application temperature range: 60–90°F (16–32°C) for application and cure.
- Optimal temperature range: 70–85°F (21–29°C) for best flow and leveling performance.
- Not for spray: T0031 is not recommended for spray application. Where a retarder reducer is required for spraying, T0005 should be used.
Typical use scenarios
- High-finish yacht topsides and superstructures: When brushing Awlgrip Topcoats and a longer open time is required to minimize lap marks and achieve a smoother film.
- Brush and roller priming: When applying 545 Epoxy Primer or Awlquik Primer/Surfacer by brush or roller and improved flow and leveling of the primer coat is desired.
- Warm to moderate climates: Where temperatures fall within 60–90°F (16–32°C) and a controlled, slow drying reducer improves workability.
FAQ – AWLGRIP SLOW DRYING BRUSHING REDUCER
-
What is AWLGRIP SLOW DRYING BRUSHING REDUCER used for?
It is a slow-evaporating thinner used in Awlgrip Topcoats, 545 Epoxy Primer and Awlquik Sanding Surfacer when these products are applied by brush or roller. It improves flow, leveling and appearance of the final film.
-
Can I use this reducer for spray applications?
No. T0031 is not recommended for spray applications. If a retarder-type reducer is required for spraying, T0005 Hot Weather Reducer should be used instead.
-
How much reducer should I add to Awlgrip Topcoat?
For Awlgrip Topcoats, add T0031 at 10–33% of the total mixed volume of color base plus converter.
-
What temperature range is recommended when using this product?
Best results are achieved when application and cure temperatures are between 60–90°F (16–32°C), with an optimum range of 70–85°F (21–29°C).
-
Is AWLGRIP SLOW DRYING BRUSHING REDUCER hazardous?
Yes. It is classified as Acute Toxicity Category 4. It is harmful in contact with skin and if inhaled (H312, H332). Appropriate personal protective equipment and ventilation are required.
-
What is the main ingredient?
The reducer contains ≥ 90% 2-butoxyethyl acetate.
-
Is it water soluble?
No. It is not soluble in cold water.
-
Can this product be used by consumers?
The safety data sheet specifies professional and consumer use as identified uses, but also notes that the product is for professional use only. Always follow local regulations and safety guidance.
-
Does it pose environmental hazards?
The mixture is not classified as hazardous to the environment, but it must not be allowed to enter drains or watercourses. Spills and waste must be managed according to regulations.
-
What is the VOC content?
The VOC content of the reducer is approximately 940 g/L or 7.8 lb/gal.
Section 14 – Transport information
According to the supplied documentation, AWLGRIP SLOW DRYING BRUSHING REDUCER (Slow Brush Reducer OT0031) is not regulated for transport under ADR/RID, IMDG or IATA.
- UN number / ID number: Not regulated.
- UN proper shipping name: Not regulated.
- Transport hazard class(es): Not regulated.
- Packing group: Not regulated.
- Environmental hazards: No.
- Transport within user’s premises: Always transport in closed containers that are upright and secure. Ensure that persons transporting the product know what to do in the event of an accident or spillage.
- Transport in bulk according to IMO instruments: Not applicable.
Section 8 – Recommended personal protective measures
Exposure controls and general hygiene
- Use only with adequate ventilation. Where necessary, employ local exhaust ventilation or process enclosures to keep airborne concentrations below applicable limits.
- Wash hands, forearms and face thoroughly after handling, before eating, drinking or smoking and at the end of the working period.
- Remove contaminated clothing and protective equipment before entering eating areas and wash contaminated garments before reuse.
- Ensure that eyewash stations and safety showers are located close to the work area.
Eye and face protection
- Wear safety eyewear complying with an approved standard when a risk assessment indicates potential exposure to splashes, mists or vapors.
- Where contact is possible, use safety glasses with side shields unless a higher level of protection is indicated.
Hand protection
- Use chemical-resistant, impervious gloves complying with an approved standard whenever handling the product, if indicated by a risk assessment.
- For prolonged or frequently repeated contact, gloves with protection class 6 (breakthrough time > 480 minutes according to EN374) are recommended. Recommended materials: Viton or nitrile, thickness ≥ 0.38 mm.
- For brief contact, gloves with protection class 2 or higher (breakthrough time > 30 minutes according to EN374) are recommended. Recommended material: nitrile, thickness ≥ 0.12 mm.
- Replace gloves regularly and immediately if they show any sign of damage. Performance may be reduced by physical or chemical damage or poor maintenance.
Skin and body protection
- Wear suitable protective clothing selected according to the task being performed and the risks involved. Clothing should be approved by a safety specialist before use.
- Use suitable protective footwear and any additional skin protection measures where required by the risk assessment.
Respiratory protection
- Based on the hazard and potential for exposure, select a respirator that meets the appropriate standard or certification.
- Respirators must be used within a structured respiratory protection program ensuring correct selection, fitting, training and maintenance.
Environmental exposure controls
- Check emissions from ventilation or process equipment to ensure compliance with environmental protection legislation.
- Where necessary, use fume scrubbers, filters or engineering modifications to reduce emissions to acceptable levels.
*Contenido generado por IA
